Overhead Crane Maintenance Service in UAE:
Overhead Crane Maintenance Service in UAE

Your overhead crane will need regular maintenance, just like a car or any other part of the machine, to increase its life and keep it running efficiently. Crane-related issues are something every machine owner should worry about, as buying a crane can be a significant investment, the investment you need to take care of. So it is about overhead crane maintenance service in UAE.

It is recommended that a regular inspection schedule be established for the crane. One must follow the manufacturer's advice for service and maintenance intervals and consider cycle and environmental factors when designing the crane to help extend the life of the crane and crane components. TECHNOMAX Middle East Engineering LLC provides comprehensive Overhead Crane Maintenance Service in UAE.

Common problems with overhead cranes:

Overhead Crane Maintenance Service in UAE
Overhead Crane Maintenance Service in UAE

1. Damage to the Wire Rope:

 Damage to the wire rope is considered a common problem that you may experience with an overhead crane. Several common wire rope problems like the wire rope may jump out of the reeving system, Reduction of rope diameter below nominal – loss of core support, internal or external corrosion, wear of outside wires, Broken or worn outside wires, Corroded or broken wires at end connections. Therefore, Overhead Crane needs Maintenance Services. Contact us to avail Overhead Crane Maintenance Service in UAE.

The best way to prevent the failure of a wire rope is to inspect it before each shift. If any evidence of damage is observed, the wire rope should not be used to prevent further usage. Also, make sure that the wire rope is adequately lubricated.

2. Crane Skew & Alignment problems:

The problem with a crane that is not working correctly is the overtime forces that didn't consider in the design and installation of the overhead crane can cause stresses to the runway beams.

These stresses can result in undesirable Accidents, Crane failure, Equipment downtime and productivity loss, cost repair, and parts replacement. Due to these problems, Technomax is specialised in providing Overhead Crane Maintenance Service in UAE.

3. Excessive Wear to End Truck Wheels:

 End truck wheels are components of overhead cranes that can require time to time maintenance, replacement, or adjustment. Over time, the wheels will wear down due to everyday use of the crane and will need to be replaced.

The wheels can be made from various materials, including gantry crane, polyurethane, alloys and low carbon steel. The more carbon there is in the steel, the more complex the wheel will be. There are also heat treatment methods that can be used to increase the hardness of a wheel, increasing the durability and load capacity of the wheels.

If the wheels, bearings or wheel flanges begin to wear or break, it could indicate that the crane is leaning and not following the track properly. Tilting the crane can cause excessive wear and stress on the wheels and the rails and support structures. Overhead Crane Maintenance Service in UAE is yet another condition monitoring service provided by Technomax.

4. Issues with the Electrification System:

 There are several problems with the electrification system of an overhead crane that may require service or future maintenance. One of the most frustrating problems that a crane operator can encounter is contacting interruptions between the conductor bars and collector.

In the collector, a carbon graphite brush can wear out, which can cause the accumulation of carbon graphite. Since carbon graphite powder is a conductive material, this build-up can cause short circuits in the electrical connection. Overhead Crane Maintenance Service in UAE provided by Technomax are considered one of the best in the entire UAE.

In older crane systems, the copper rails on the conductive bars can also rust or oxidize due to the operating environment or extended periods when the crane is not used. To prevent this from happening, conductor bars and manifolds should be inspected and cleaned regularly to ensure contact between the collector and the conductor bar is uninterrupted.

5. Bent or Damaged Hooks:

It is designed to hold a load in a specific and precise direction. When the weight is not directed as per the design, it compromises the creation of the hook and can increase the possibility of bending, stretching or breaking. The load can also slip off the hook if it extends from the throat opening. At the beginning of each shift, a regular inspection of the hooks and other fasteners should be performed to check for deformity or damage. We have solution for your every problem of Overhead Crane Maintenance Service in UAE.

While there are no clear guidelines on the use of hook latches, we train our employees and inspectors. We advise the end-user to evaluate the work activity concerning the safety of their employees. If the action makes using the lock impractical, unnecessary, or more dangerous, the end-user can choose to delete the lock. It is also recommended that each lifting activity be considered independently of the use of a hook lock.

Contact us for Overhead Crane Maintenance Service in UAE.

All rights reserved. © Technomaxme.com | Terms & Conditions

Designed by webandcrafts.com